combining surface造句
例句與造句
- 2 ) after combining surfaces , two surface curvature is continuous
2 )兩曲面之間的拼接可以達到c2連續,滿足曲面建模的要求。 - 3 ) when combining surfaces with vertex , surfaces c1 continuous at vertex , c2 continuous other . so , it approve the methods are effective
3 )多曲面有角點拼接時,角點處可以達到g1連續,其它地方達到c2連續。 - The quantitative analyses of three lubricating oil wedge bearing are contributive to understand the dynamics performance of three lubricating oil wedge bearing with horizontal combine surface . the priman research contents of the thesis and its contributions are as followed : 1
論文完成的三油楔平切瓦水平結合面存在貫通的縫隙時軸承動力特性的定量分析結果,可以加深我們對三油楔平切瓦動力特性的認識,具有重要的學術意義。 - In this thesis , the overall optimization designs on surface - emitting lasers with 45 deflector structure are carried out . we have mainly considered two types of surface - emitting lasers with 45 deflector : surface - emitting lasers with 45 intracativity micro - mirrors and combined surface - emitting lasers , and then designed detailed fabrication processes
本論文對45偏轉鏡面發射半導體激光器結構進行了優化設計,具體考慮了兩種45偏轉鏡面發射半導體激光器:折疊腔面發射和組合式面發射,設計了具體的工藝過程。 - After studying a lot of documents of computer - graphics and computation of geometrical , based on nurbs , which is a pop expression to describe curve and surface , the author put forward a method ? ? to identify bad point by most excursion , to illustrate how to choose smooth base plane , which is not referred in most documents , and to introduce optimize method of operational research to combine surfaces , especially for surfaces combination with vertex , and improvement of combination effect
在解決多曲面有角點的拼接問題中引入了運籌學的優化方法,改善了多曲面拼接的效果,而且在ugii造型軟件的基礎上,用visualc + + 、 ug / openapi進行二次開發,加入了壞點剔除,曲線光順,曲面片之間的拼接等功能,很好的解決了反求工程中所遇到的問題。 - It's difficult to find combining surface in a sentence. 用combining surface造句挺難的
- According to the analytical method of sub structure , we combine the finite elemental model of different parts and process the combining surface parameter to build the finite elemental model of the system . using the ansys software , we carry on the finite element mode analysis to get the natural frequency and shaking type
根據動態設計的子結構分析方法,將上述系統主要部件的有限元模型組合并分析處理結合面參數構成系統的有限元模型。利用ansys有限元分析軟件,對系統進行有限元模態分析,確定系統的各階固有頻率和振型。 - 2 ) for making the meshes consistent on the common boundaries of adjoining surfaces , a new approach of boundary discretization is employed . 3 ) the boundary - representation structure is adopted to fulfill the mesh generation over combined surfaces . 4 ) the quality of surface meshes is improved by point creation on 3d scan lines and diagonal swapping procedure
通過引入可移動的虛邊界解決了閉合曲面的剖分問題;通過對鄰接曲面公共邊界的統一處理,保證了組合曲面拼合處網格的相容性;以邊界表示數據結構為基礎實現了三維組合曲面的全自動網格剖分;采用空間掃描線布點、診斷交換等技術,優化了網格的質量;并以autocad為支撐平臺objectarx為開發工具,開發了一個基于幾何造型的曲面三角形網格全自動生成程序。 - The numerical calculating based on reynolds equation are carried out with the help of computer program built by bearing research institute of xi ' an jiaotong university . the calculating results indicated that three lubricating oil wedge bearing with an end - to - end through gap between the horizontal combine surfaces will not be unsteady factor when the bearing load no change . but the horizontal oil film rigidity will reduce and the working position of axle journal in the bearing will change
論文利用雷諾方程對# 5軸承的三油楔水平中分軸承進行了數值計算,計算結果表明,當三油楔軸承水平中分面有貫通的縫隙而軸承的載荷不變時,三油楔軸承不會失穩,但會減小水平方向的油膜剛度,改變軸頸在軸瓦中的工作位置。 - This static finite element modeling method does n ' t need the requirement of the dynamic design of product in the modern industry . otherwise , most work on the surface mesh generation is based on the single trimmed surfaces , and the work to closed surface and combined surface , which are very popular in engineer , is very few
另外,在曲面網格劃分方面,當前的研究大多是針對單張非閉合曲面進行的,對于閉合曲面和組合曲面的研究甚少,而這些曲面在實際工程中卻是經常使用的。